高功率横流CO2激光器脉冲预电离过程研究

本文给出了对高功率横流CO_2激光器脉冲预电离过程的理论和实验研究.表明了预电离过程中光电离的重要作用.实验结果表明,脉冲预电离可增大高功率横流CO_2.激光器的pd值(p为放电气压、d为放电间隔),增大放电区注入功率密度.对于提高此类型激光器的放电稳定性和输出激光功率是一种技术简单而有效的手段.     

离心泵在启动阶段的水力特性研究

针对工作的离心泵,分析了其内部流体的流动情况,建立了在非稳定工况下操作的理论扬程公式,非稳态理论扬程包括旋转加速附加扬程和水流加速消耗扬程以及由于流动速度变化引起泵壳中的附加压力而产生的扬程。在离心泵的启动阶段,对其在不同阀门开度下的水力性能进行了试验研究。测量了瞬时转速、流量、扬程随时间的变化关系,并把试验结果进行修正。由于启动时一部分扬程用来提供流体加速,压力传感器测量不到,因此必须把试验扬程加以修正。将理论计算与修正的试验结果进行了比较分析,两者基本吻合。     

Investigation on Ochratoxin A stability using different extraction techniques

The stability of Ochratoxin A during its extraction using different extraction techniques has been evaluated. Microwave-assisted extraction and pressurised liquid extraction, in addition to two other reference methods of extraction, i.e. ultrasound-assisted and magnetic stirring-assisted extraction, were evaluated. The effect of extraction temperature using the cited techniques was checked.The results show that Ochratoxin A can be extracted using microwave-assisted extraction at temperatures up to 150 °C without degradation. Pressurised liquid extraction can be used at temperatures up to 100 °C, for extraction times of less than 30 min. Further, both ultrasound-assisted extraction and magnetic stirring extraction can be applied at temperatures up to 65 °C.High-performance liquid chromatography combined with fluorescence detection using a Chromolith RP-18e column at a flow rate of 5 mL min⁻¹ was used to quantify the Ochratoxin A. The retention time for the Ochratoxin A was 1.3 min. The limits of detection (LOD) and of quantification (LOQ) were 0.03 and 0.10 μg L⁻¹, respectively.     

HPLC-MS/MS技术在中华绒螯蟹硝基呋喃类代谢物残留量检测中的应用

建立了中华绒螯蟹中硝基呋喃类代谢物残留量的液相色谱-串联质谱检测方法.取均质后的中华绒螯蟹可食部分样品,用盐酸水解组织中蛋白结合代谢物,经2-硝基苯甲醛37℃过夜衍生化,调节pH值至约7.0～7.4后,用乙酸乙酯提取,正己烷净化.选用电喷雾离子源,在正离子、多反应监测方式模式下进行定性,以同位素内标法进行定量.方法的检出限为0.5 μg·kg-1,工作曲线的线性范围为1.25～50.0 μg·L-1.在添加浓度为0.5～10.0 μg·kg-1的范围内,AMOZ、SEM、AHD和AOZ的回收率分别在92.8%～106%、84.5%～94.6%、80.6%～98.6%和88.4%～105%之间,相对标准偏差均小于10%.     

Dextran-modified iron oxide nanoparticles

Dextran-modified iron oxide nanoparticles were prepared by precipitation of Fe（Ⅱ） and Fe（Ⅲ） salts with ammonium hydroxide by two methods. Iron oxide was precipitated either in the presence of dextran solution, or the dextran solution was added after precipitation. In the second method, the iron oxide particle size and size distribution could be controlled depending on the concentration of dextran in the solution. The nanoparticles were characterized by size-exclusion chromatography, transmission electron microscopy and dynamic light scattering. Optimal conditions for preparation of stable iron oxide colloid particles were determined, The dextran/iron oxide ratio 0-0,16 used in precipitation of iron salts can be recommended for synthesis of nanoparticles suitable for biomedical applications, as the colloid does not contain excess dextran and does not coagulate.     

Mutual solubilities of hydrocarbons and water with the CPA EoS

The knowledge of hydrocarbon/water phase equilibria is important in the design and operation of equipment for petroleum transport and refining and petrochemical plants. The presence of water in a hydrocarbon mixture can affect the product quality and damage the operation equipment due to corrosion and formation of gas hydrates. Tracing the concentration of hydrocarbons in aqueous media is also important for technical purposes like preventing oil spills and for ecological concerns such as predicting the fate of these organic pollutants in the environment.     

Developing a hybrid emulsion polymerization system to synthesize Fe3O4/polystyrene latexes with narrow size distribution and high magnetite content

A hybrid emulsion polymerization was formulated for synthesizing Fe₃O₄/polystyrene composite latex. This system, containing binary droplets that are magnetic (Mag)‐droplets with a diameter of 100–200 nm and styrene (St)‐droplets with a diameter of 3–4 μm, was obtained by mixing Mag‐miniemulsion and St‐macroemulsion. With extremely low surfactants concentration (?critical micelle concentration, CMC), the nucleated loci are selectively controlled in the Mag‐droplets, as the result of smaller droplet size and larger surface ratio. Both water‐soluble potassium persulfate (KPS) and oil‐soluble 2,2′‐azobis(2‐isobutyronitrile) was adopted to initiate the polymerization. In the presence of KPS, magnetic polystyrene latices with particles size of 60–200 nm, narrow size distribution, and high magnetite content (86 wt % measured by TGA) were attained successfully. The synthesized magnetic Fe₃O_4/polystyrene latices assembled into well‐ordered hexagonal structure in the surface of a carbon supported copper grid. The influence of various parameters on various aspects of the as‐synthesized Fe₃O₄/polystyrene was investigated in detail: type of initiator on composite morphology, feed ratio of Mag‐miniemulsion and St‐macroemulsion on magnetite content, and hydrophobic agent or amount of surfactant on size and size distribution. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5285–5295, 2007     

Diblock copolymers based on allyl methacrylate: Synthesis,characterization, and chemical modification

Different diblock copolymers constituted by one segment of a monomer supporting a reactive functional group, like allyl methacrylate (AMA), were synthesized by atom transfer radical polymerization (ATRP). Bromo‐terminated polymers, like polystyrene (PS), poly(methyl methacrylate) (PMMA), and poly(butyl acrylate) (PBA) were employed as macroinitiators to form the other blocks. Copolymerizations were carried out using copper chloride with N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) as the catalyst system in benzonitrile solution at 70 °C. At the early stage, the ATRP copolymerizations yielded well‐defined linear block copolymers. However, with the polymerization progress a change in the macromolecular architecture takes place due to the secondary reactions caused by the allylic groups, passing to a branched and/or star‐shaped structure until finally yielding gel at monomer conversion around 40% or higher. The block copolymers were characterized by means of size exclusion chromatography (SEC), ¹H NMR spectroscopy, and differential scanning calorimetry (DSC). In addition, one of these copolymers, specifically P(BA‐b‐AMA), was satisfactorily modified through osmylation reaction to obtain the subsequent amphiphilic diblock copolymer of P(BA‐b‐DHPMA), where DHPMA is 2,3‐dihydroxypropyl methacrylate; demonstrating the feasibility of side‐chain modification of the functional obtained copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3538–3549, 2007     

Quantification of trace elements in human serum fractions by liquid chromatography and inductively coupled plasma mass spectrometry

On‐line coupling of LC and ICP‐MS has been used for fractionation and detection of species of Cu, Fe, I, Se and Zn in human serum. It has been shown that anion exchange chromatography provided better separation capability (both intra‐ and inter‐element) than size‐exclusion chromatography. The mobile phases for ion exchange chromatography consisted of Tris–HNO₃ buffer and ammonium salt (nitrate, acetate or formate). Formate was found to be the best mobile phase counter ion, enabling good chromatographic separation, and is acceptable for mass spectrometry too. The quantitative evaluation of element concentrations adhering to individual fractions was performed by the peak area normalization method. The repeatability of results ranged from 3 to 15% (depending on the element concentration level) and represented the main part of the result uncertainty. The accuracy of Cu and Zn fraction determinations was confirmed by comparison with the isotope dilution technique. Copyright © 2006 John Wiley & Sons, Ltd.     

医疗保险索赔数据的广义Pareto分布拟合

How to choose an optimal threshold is a key problemin the generalized Pareto distribution (GPD) model.This paper attains the exactthreshold by testing for GPD,and shows that GPD model allows the actuary to easily estimate high quantiles and the probable maximum loss from the medical insurance claims data.